ASTROSTART J5F-TX2000 keyless remote car starter control transmitter J5FRS-2T

Description: Normal 0 false false false EN-US X-NONE X-NONE One ready-to-program with battery-installed Remote for your aftermarket Astrostart or Astroflex installed security system This item is pre-owned – it will work like new once programmed to your vehicle One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement PRE-OWNED for OEM FACTORY AFTERMARKET AFTER MARKET KEY REMOTE KEYLESS ENTRY FOB ALARM REPLACEMENT TRANSMITTER KEYFOB CLICKER CONTROLLER STARTER CAR START AUTOSTART CONTROL TRANSMITTER FUNCTIONS AT 100% TESTED & GUARANTEED Astrostart FCC ID: J5FRS-3T P/N: 310-052-163 Model #: 1066-2 Part #: 310-052-166 Alternative FCC ID: J5F-TX2000 (Alternate Spelling: J5F-TX2OOO) (Interchangeable FCC ID: J5FRS-2T) Part #: 310-052-166 Model #: 1066-2 Frequency: 372.5 MHz LED color: RED 2 buttons REMOTE MADE FOR: ASTROSTART / ASTROFLEX ® BUTTON: 2 LED or LIGHT: GREEN BOARD#: 372.5Mhz FCC ID: J5FRS-3T P/N: 310-052-166 Compatible with the following systems: RS-101 RS-102 MV-801 MV-802 502 1003 1004 Programming Instructions: Instructions for programming your new Code Alarm Remote(s) Note: Each System module has four “slots”, or memory locations, to store transmitter codes, giving it the ability to operate from up to four transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters: · One Remote Transmitter – Program four (4) times · Two Remote Transmitters – Program each transmitter two (2) times. · Three Remote Transmitters – Program two transmitters one (1) time, and the remaining transmitter twice. 1. Open the driver’s door, leave the door open and make sure the dome light is ON. 2. Turn vehicles ignition on (Ignition ON engine OFF). 3. Press and hold emergency override button (A small black headed push button commonly found under the driver side dash) After about 10-13 seconds, the siren or horn will sound three (3) times. This indicates that the unit has entered the transmitter-programming mode. 4. Continue to hold in the programming override button. 5. Press the ARM (or LOCK) button on the remote transmitter to be programmed. The siren or horn will sound once, indicating that the system has “learned” that remote transmitters code. 6. Repeat step 5 for any additional transmitters or transmitter codes. 7. Release the programming override button. 8. Turn the ignition off to exit the programming mode. Test remote transmitters to ensure that they work properly by toggling back & forth the LOCK and UNLOCK buttons. SECOND METHOD J5FRS-3T 792 / 784 Programming Instructions: Instructions for programming your new Code Alarm Remote(s) Note: Each System module has four “slots”, or memory locations, to store transmitter codes, giving it the ability to operate from up to four transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters: · One Remote Transmitter – Program four (4) times · Two Remote Transmitters – Program each transmitter two (2) times. · Three Remote Transmitters – Program two transmitters one (1) time, and the remaining transmitter twice. 1. Open the driver’s door, leave the door open and make sure the dome light is ON. 2. Turn vehicles ignition on (Ignition ON engine OFF). 3. Press and hold emergency override button (A small black headed push button commonly found under the driver side dash) After about 10-13 seconds, the siren or horn will sound three (3) times. This indicates that the unit has entered the transmitter-programming mode. 4. Continue to hold in the programming override button. 5. Press the ARM (or LOCK) button on the remote transmitter to be programmed. The siren or horn will sound once, indicating that the system has “learned” that remote transmitters code. 6. Repeat step 5 for any additional transmitters or transmitter codes. 7. Release the programming override button. 8. Turn the ignition off to exit the programming mode. Test remote transmitters to ensure that they work properly by toggling back & forth the LOCK and UNLOCK buttons. Nnnnnnn nnnnnnnnn bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb remote requires programming to work with your compatible system. see below Please note there are several compatible remotes that look similar but not exactly like the photo pictured. We will do our best to ship you the remote pictured; however, the remote you receive may look different than the remote pictured. No worries, the board will program to your system the same. Condition Explanation: Pre-Owned Pre-Owned: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections.

Price: 25.59 USD

Location: Wellsboro, Pennsylvania

End Time: 2024-12-29T14:19:29.000Z

Shipping Cost: 6.96 USD